Multiple samples can be processed simultaneously in the Benchmixer XLQ’s large capacity racks, saving time and preventing operator fatigue. The vigorous, consistent shaking ensures all samples are exposed to identical conditions within the same batch of samples, as well as between batches.

The BenchMixer XLQ creates a true vortex in vertical sample racks by holding the top of the tube stationary while the bottom rotates in a 3.6mm orbit. Time and speed are precisley controlled by the digital microprocessor. A pulse mode allows for more vigorous mixing. Quiet operation, minimal vibration and a long service life are guaranteed by the precisely balanced drive system and powerful motor.

Using the BenchMixer XLQ is simple. To load the sample racks, loosen the knobs on the stationary steel rods and raise the top sample plate. One rod is shorter than the other, allowing the plate to be lifted up and swiveled to one side. After samples are loaded, lower the plate into place and tighten the knobs. Select the desired speed and run time on the digital control panel and press start. The BenchMixer XLQ can perform unattended mixing for as little as 1 minute or up to 100 hours.
 

• For use with QuEChERS and other sample prep methods
• Powerful, hands-free shaking/vortexing
• Pulsing program for interval mixing
• Supplied with QuEChERS rack starter kit: 7 x 50ml tubes, held horizontally 50 x 15ml tubes, held vertically 50 x 1.5/2.0ml tubes, held vertically

The 7×12 inch platform accommodates a wide variety of standard, pre-drilled tube racks (a complete listing can be found in the ordering information section below). Additionally, BenchMixer XL can easily be adapted to almost any type of vessel commonly found in the laboratory (contact us for details).

Using BenchMixer XL is easy; after loading the sample rack and tightening the locking knobs, select the desired speed and run time on the large digital control panel. Then, simply press “Start” and the BenchMixer XL will perform unattended mixing for up to 100 hours.

BenchMixer XL’s large capacity and adaptability make it an ideal choice for
the medium to high throughput laboratory.
 

• Hands-free, high capacity vortexing
• Up to 2500rpm, a true vortex in every tube
• Assortment of accessories for a variety of tubes, flasks & plates
• Pulsing program for interval mixing
• Fits almost any tube rack

The drive system is balanced with Q-Drive™ technology, providing a smooth vortexing action, while minimizing noise and excessive vibration. This results in quieter, more efficient and longer lasting operation. Increased speed, up to 3400 rpm produces an instant vortex of even the largest sample sizes, including full 50ml tubes.

Other features include: “no-walk” suction feet, cold room/incubator compatibility and spill-proof electronic controls.
 

• Unique Multi-Head™ for general purpose vortexing PLUS holds up to eight microtubes (Patent Pending)
• Powerful motor for INSTANT vortexing
• Continuous or “touch” operation
• Q-Drive™ dynamic balancing system
• Variable speed from 200 to 3400 rpm
• Wide variety of accessories

Insta-Touch operation means that the motor is automatically activated with slight pressure on the center cup head. Operation is smooth, quiet and efficient. When pressure is removed, operation immediately ceases.

The Vornado’s unique head design prevents liquids from entering the housing, prolonging motor life. The unit is available with five different cup head colors
 

• Powerful vortexing for tubes up to 50ml
• Inst-Touch™ pressure activated operation
• “Mini Sized”, less than 4 in. wide
• Available in five color configurations

– A large back-lit, liquid crystal display
– High capacity rotor, 8 tubes up to 15ml (conical or round bottom)
– Unique EZ-Scroll™ touch pad
– Timer up to 99hr 99mins. / continuous
– Storage of commonly used run-times
– Control of speed in in both rpm and rcf
– Adjustable acceleration and deceleration levels
– Safety imbalance detection system
– Momentary operation
– Electrical lid lock

Ideal for rapid production of serum and plasma
 

• 8 Position fixed angle rotor rotor
• Ideal for rapid production of serum and plasma
• Unique EZ-Scroll™ touch pad
• Digital speed control in rpm or rcf with adjustable acceleration and deceleration rates (up to 6,800rpm/4,445xg)
• Program storage up to 99
• Adjustable speed and timer

– Increased speed up to 4,000rpm / 2850xg
– Back-lit, liquid crystal display
– Adjustable speed in increments of 100rpm
– Digital speed control in rpm or rcf
– Adjustable acceleration and deceleration levels
– A safety imbalance detection system
– Momentary operation
– High capacity rotor for tubes up to 15ml (conical or round bottom)

In addition, the Sprint™ 6H PLUS offers an optional fixed-angle rotor for centrifugation of up to 12 tubes.
 

• 6 Position horizontal (swing out) rotor
• Holds all common blood collection tubes up to 15ml
• Digitally set speed in rpm or rcf (up to 4,000rpm/2,850xg)
• Adjustable speed and timer
• Safety imbalance detection system

Designed for use with 10ml tubes (16 x 100mm), smaller tubes (12 x 75mm and 12 x 100mm) can be centrifuged using the optional adapters (item: C3100-ADP).

With intuitive controls and a large LED display, virtually no programming or setup is required prior to starting a cycle. Simply select the run time and press “START”. The safety lid-lock is engaged and the rotor quickly and smoothly accelerates to 3,400 rpm. Once the run time is completed (or the “STOP” button is pressed) the rotor comes to a complete stop and the lid lock is disengaged for removal of samples.
 

• 6 Position horizontal (swing out) rotor
• Holds all common blood collection tubes up to 10ml
• Designed specifically for blood, urine, and cell separations
• Adjustable timer
• UL Listed

The back-lit, liquid crystal display provides full control over the set run time and rotational speed. The rotational speed can be set/viewed in rpm or rcf and acceleration/deceleration levels can be easily adjusted in the advanced settings mode.

To ensure safety, the digital microprocessor ensures that the lid has been closed and that the safety lid lock is engaged prior to starting a centrifugation cycle. In addition, an advanced imbalance detection system constantly monitors the balance and vibration, automatically bringing the rotor to a stop if an imbalance is detected.
 

• Digital Speed control up to 5,000 rpm
• Safety lid-lock, prevents opening lid until rotor stops
• Unique air-flow design keeps samples cool
• 8 tube capacity, for tubes up to 15ml

• Wet, dry or cryogrinding
• Accepts a variety of tubes, plates and jars
• Large, digital touch screen control panel
• See-though safety lid

• High capacity – 24x2ml
• Cooling function to protect temperature sensitive samples
• True refrigeration – no dry ice, liquid nitrogen or external connections
• Sealed 2.0ml tubes – eliminates cross contamination
• Full range of beads in prefilled tubes and bulk available

• Ideal for cell disruption, DNA shearing and ChIP assays
• Programmable with touch screen control and pulsed operation
• 150W, for volumes 0.1 to 150 ml (requires appropriate horn)
• Supplied complete with 6mm horn, temperature probe and soundproof enclosure

The D1000 is a rotor stator homogenizer, and works by drawing the sample, in liquid, into the generator probe with the variable speed rotor, and then forcing it out through the slots in the stator. This achieves mechanical shearing of the sample. As the sample is repeatedly drawn up and forced through the stator, additional shearing takes place. Most samples are completely homogenized in 30 seconds are less. A powerful, 130W motor drives the rotor at speeds from 8,500 to 30,000 rpm. Speed is adjustable in six steps to meet sample processing needs. A separate on/off switch allows the homogenizer to be left at the appropriate setting.

Generator probes are available in four sizes. The 5mm and 7mm diameter have a 50mm length for use with samples in microbtubes. The 10mm x 115mm is ideal for use with 15 and 50ml tubes and 14mm x 130 mm, for 50ml tubes and vessels up to 250ml. The unit is supplied with one each of the 5mm and 7mm generator probes. All the generator probes are made of stainless steel and can be sterilized by autoclaving.
 

• Homogenize most samples in under 30 seconds
• For volumes from 100µl to 250ml
• Supplied with both 5mm & 7mm generator probes

Mini BlotBoy™ and BlotBoy™ are supplied with autoclavable flat mats and are ideal for blot washes and gel staining/destaining. Both models have been designed to conserve bench space. The Mini BlotBoy is supplied with a 10.5 x 7.5 inch platform while the larger BlotBoy’s 12 x 12 inch platform expands the useable work surface by 80%.

The Mini BlotBoy and BlotBoy can accept stackable platforms and handle loads up to 2kg. Both have maintenance free brushless motors and are safe for use in cold rooms and incubators.
 

• Optimized speed and tilt for gel blotting, washing & staining
• Tri-directional motion for thorough, gentle mixing
• Optional stacking platforms availableCold room and incubator safe

Both models come standard with autoclavable dimpled mats while optional flat mats are also available for mixing other vessel types. Stacking platforms can be purchased as accessories, effectively doubling the usable surface area of each model.

Even the smallest single platform configuration has 24% more platform work surface than traditional nutating mixers.

These mixers feature maintenance free, brushless motors capable of loads up to 2kg and are safe for use in cold rooms and incubators.
 

• Includes dimpled mat; ideal for mixing in blood & centrifuge tubes
• Tri-directional motion for thorough, uniform mixing
• Optional stacking platforms available
• Cold room and incubator safe

This model includes both flat and dimpled (autoclavable) mats for mixing a wide variety of tubes and other vessels.
Stacking platforms can be purchased as accessories, effectively doubling the usable surface area of each
model.

BenchRocker 3D features a maintenance free, brushless motor, capable of loads up to 4.4 lbs and is safe for use in
cold rooms and incubators.
 

• Adjustable speed & tilt for a wide range of applications
• Large 12 x 12 in. work surface
• Insta-TILT™ technology for instant adjustment to the tilt angle
• Dual platform accessory doubles work surface
• Cold room and incubator safe

The tilt angle is instantly adjustable (no tools or disassembly required) from 0 to 10° and the mixing speed can be adjusted from 5 to 105 rpm, using the large, user-friendly LCD control panel. Combined control of both parameters (tilt and speed) makes the BenchWaver a versatile workhorse that can provide anything from gentle, slow moving waves to a rapid, more vigorous motion. Additionally, time of operation can be selected from1 minute up to 99 hours or for continuous operation.

The large 13.5 x 13 inch platform is supplied complete with a non-slip, rubber mat. An optional stacking platform is available for users requiring additional mixing capacity. BenchWaver is a reliable and versatile instrument and can be used in refrigerated or incubated.
 

• Undulating, 3-dimesional motion
• Adjustable speed and tilt angle
• Large, 13 inch platform
• Ideal for staining, washing & general mixing

As the roller mechanism rotates through each complete revolution, the right side of each roller is gently elevated about 0.5 in (13mm) and returns to the horizontal starting position. This additional, gentle up/down motion provides a “wave” effect and guarantees that the entire sample is subjected to complete, thorough mixing, end to end. This built in tilt feature provides a level of homogeneous mixing uniformity that can not be matched by any stationary roller apparatus.

From blood collection tubes to roller bottles, Benchmark TubeRollers are the ideal choice for research, clinical laboratories and doctors’ offices.
 

• Gentle rolling motion
• Smooth +/-5° tilt action
• For tubes/bottles from 8mm to 200mm diameter
• Two models: 5 roller and 10 roller

For applications requiring temperature control, the Roto-Therm series can be digitally programmed to maintain chamber temperatures of ambient +5°C to 60°C and include an “in-lab” calibration function for ensuring accurate temperature control.

The Roto-Therm is also available in a “Plus” configuration, providing the following additional features:

Variable speed:           5 to 70rpm
“Mix” function:            Rotating in combination w/ oscillations (increased mixing)
“Pause” function:        Rotating with intermittent “stops” during rotation
“Rock” function:          Back and forth, gentle rocking motion (see-saw)

The Plus model also offer an additional rocking platform (4.5 x 3 in.), as well as a 96 x 0.2ml tube/strip/plate holder for mixing PCR vessels in the “Mix” (oscillating) mode.
 

• Rotated mixing with temperature control
• Includes tube holders for common tube sizes
• Available with variable speed control and advanced shaking/ mixing modes: Mix (Oscillating), Pause, Rock

The RotoBot and RotoBot Mini each inlcude an assortment of vertical tube holders. The Mini model is supplied with holders for 12 x 1.5ml tubes, 2 x 15ml & 2 x 50ml tubes; the standard model, 30 x 1.5/2.0ml, 8 x 15ml & 2 x 50ml tubes. For higher capacity applications, more of these holders can be purchased as accessories. In addition, horizontal holders are available for applications such as Western blotting and hybridization. The unique, sliding attachment allows for quick and easy changing of tube holders.

For rocking applications, a platform with a non-slip rubber mat is available. Once attached, simply select the “PP” mode to turn the rotator into a platform rocker.
 

• Advanced programming with a wide variety of rotational modes
• Set for full 360° rotation, or interrupt rotations with pausing & mixing intervals
• Slow rotating to vigorous mixing
• Cold room and incubator safe
• Accepts common tubes from 1.5 to 50ml
• Optional rocking platform

Three rotisserie tube holders are included for mixing all common laboratory sample tubes and each individual tube holder is rubber coated to provide a secure grip, preventing any “wobble” or loosening during mixing at high speeds.

For more intense mixing, a unique reversing mode is available. In reversing mode, the mixer rotates for up to 360° then stops and rotates in the reverse direction. This back and forth motion occurs repeatedly until the set time has expired.

• Adjustable speed and tilt angle
• Reversing mode, for more intense mixing
• Cold room and incubator safe
• Includes three rotisseries for all common tube sizes

• Designed to fit and maximize capacity in most CO2 incubators
• Remote control, adjust without disrupting the CO2 environment
• Horizontally circular 19mm orbit for aeration & mixing
• Instantly exchange flask clamps with MAGic Clamp™ accessories (PATENTED)

An optional MAGic Clamp™ platform is available for use with Erlenmeyer flasks and test tube racks. The unique magnetic attachment method is the easiest way to instantly change between flask clamps of different sizes. (PATENTED)
 

• Digital speed control up to 300 rpm
• Horizontally circular 19mm orbit for aeration & mixing
• Extremely compact, perfect for low to medium capacity applications
• Instantly exchange flask clamps with MAGic Clamp™ accessories (PATENTED)

The convenient MAGic Clamp™ platform (PATENT PENDING) is also available for use with Erlenmeyer flasks and test tube racks. The unique, magnetic attachment method (PATENTED) is the easiest way to instantly change between flask clamps of different sizes.
 

• High capacity, up to 9 x 500ml, 5 x 1L or 2 x 2L
• Horizontally circular 19mm orbit for aeration & mixing
• Digital speed control up to 300 rpm
• TOUCH Screen control over time, speed and temperature
• Instantly exchange flask clamps with MAGic Clamp™ accessories (PATENTED)

• Temperature control from 0 to 105°C
• Multiple block options for plates and tubes up to 50ml
• Broad temperature and speed range to meet a variety of applications

• Large touch screen for simple and easy programming and viewing of status
• Advanced programming features include adjustable ramp rates, preheat and clockwise/counterclockwise mixing
• Multiple block options for plates and tubes up to 50ml
• Broad temperature and speed range to meet a variety of applications

Designed for application flexibility, the Incu-Mixer series is available in two, and four-plate capacities. The four-plate model includes additional height for accepting deep well microplates with a maximum height of 46 mm, and the two-plate model accommodates microplates that are up to 20 mm high. Independent time, temperature and speed controls allow the mixer to function as 3 machines in one; a multi-plate incubator, vortexer, or a combination of the two. The Incu-Mixer MP series is ideal for a wide variety of molecular biology applications including immunochemical reactions, enzyme and protein analysis, and microarray analysis.

•  
• Temperature control from 0 to 100°C
• Exchangeable blocks, for tube sizes 0.2 to 50 ml
• Precision contoured wells for uniform thermal transfer
• Two models: Heat/Cool or Heat only
• Sequence link function for linking or repeating programs (HC model only)
• Blocks sold separately

• Internal microscope option
• Precision temperature control
• Excellent accuracy and recovery
• Heated door and door frame

each model includes a 12V vehicle power adapter for operating the instrument in a car, boat, etc.

Both temperature and CO2 percentage are digitally adjustable and displayed in real time on the large LED control panel. This panel also features a “Cal” function, for easy in-lab calibration of the temperature or CO2. In addition, humidity (up to 80%) can be added to the chamber by inserting the included (stainless steel) humidity reservoir.

The CO2 level is constantly monitored using dual beam infrared sensing technology. In the event of a drop in CO2 , audible and visual alarms are triggered, notifying the user of the error.

Despite its small size, the incubator features a relatively large 20L chamber with the capacity for flasks and bottles up to 2 liters. Two removable, stainless-steel shelves are included. The shelves are perforated to improve airflow within the chamber.

* If disconnected from the CO2 supply, CO2 percentage decreases by approx. 1% /30 min
 

• Digital control of temperature and CO2
• Personal sized, 13 x 14.5″ footprint (20L)
• Accepts bottles and flasks up to 2L
• Includes 2 stainless steel shelves
• Dual beam, infrared sensor

With forced air technology and stainless steel inner construction, uniform heat transfer is ensured throughout the internal chamber. When set for sub-ambient temperatures, the powerful compressor is activated, quickly cooling the chamber to the desired temperature..

With an exterior height of 39 inches (100cm), the incubator is designed to be floor-standing, yet is also compact enough for bench-use. (Not recommended for use on benchtops taller than 32″/81cm). The instrument is supplied with two, adjustable height shelves, while additional shelves can also be purchased separately (item: H2365-SH).
 

• Accurate temperature control from 0° to 60°C
• Powerful compressor maintains 0°C
• Stainless-steel internal chamber
• Internal power outlet for shaker, mixers, etc.
• For floor standing use or on bench-tops less than 32″ tall
• Ideal for BOD and Drosophila applications

Unlike other laboratory incubators, the SureTemp series offers “Dual-Convection” technology, allowing users to choose between mechanical convection mode* (for exceptional temperature uniformity) or gravity convection mode* (for longer incubations where airborn contamination or drying of samples may be an issue). The heating elements are strategically located on multiple sides of the chamber and contents can be viewed with the separate inner glass door without disrupting the temperature environment.

* Mechanical Convection: Incorporates optimally positioned heating elements in conjunction with an internal chamber fan to control the internal temperatue.
Gravity Convection: Eliminates any airflow from the chamber, relying solely on the heating elements and gravity to control the internal temperature.
 

• Precision temperature control up to 75°C
• Dual-Convection technology, excellent uniformity and recovery
• Includes SureCheck™ temperature logger and software
• Stainless steel chamber with internal power outlet

• Two separate modes for BEADS or WATER
• Quik-Cal™, simple in-lab calibration function
• Offers all of the advantages of a “Bead Bath”
  • Eliminates constant refills (Burn-out protection)
  • Easy (accessory free) securing of tubes and bottles
  • Allows angled incubations
  • Runs constant (no wait for heat-up)

The seamless, stainless steel chamber has a 12 liter capacity and includes a universal spring-loaded platform for securing 15 & 50ml test tubes, as well as Erlenmeyer flasks and media bottles up to 1 liter. A hinged and removable lid is also included to reduce energy waste, prevent splashing and divert condensation away from samples.

Easy to use controls allow the user to digitally select and monitor time, temperature and shaking speed, while a constant monitoring system ensures accuracy over each parameter.

Optional test tube racks are available for microtubes and custom-designed racks can also be made available by request.
 

• Orbital shaking motion
• Included spring platform accepts tubes, bottles and flasks
• Digital control of time, temperature and speed
• Compact design, conserves benchspace

All myBath models feature seamless, stainless steel chambers for easy cleaning and long life The chambers resist rust and have no corners to collect dirt or contamination. The larger 8L and 12L units have drains for hassle-free water changes. The 4L, 8L, and 12L models include a see-through cover that can be removed, or flipped back on a rear hinge to conserve bench space. The lid’s gabled design will divert condensation to the front and back of the bath, away from samples.

Racks are available to accommodate 1.5/2.0ml, 15ml and 50 ml tubes within the 4L, 8L and 12L baths. The myBath 4L is supplied with all three racks.

*myBath 2L (Item: B2000-2), has a 2-digit display and can be controlled in increments of 1.0C

Designed for lower throughput needs, the TC-32 Mini Thermal Cycler has a capacity for 32×0.2ml tubes. The wells are arranged in a 4×8 format, allowing the block to accept strips of 8 as well as individual tubes. The block heats and cools very quickly – at rates as fast as 5°C/second. A proprietary algorithm controls block temperature, bringing samples quickly to the target temperature without any over- or under-shoot. Excellent block uniformity ensures consistency sample to sample.

Operation of the thermal cycler is controlled from the large, full color, touch screen. Icon driven menus allow users to get running quickly. Programming is extremely simple and includes options for time and temperature increment/decrements, adjustable ramp rates, and an auto pause and restart functions. More than 100 typical programs can be stored in memory and easily recalled. After a run, samples can be held at 4°C. An on-screen report is also available at the completion of a run.

The heated lid is self adjusting – the spring loaded platen in the lid comes firmly into contact with the tops of the tubes to prevent sample evaporation and condensation. There are no knobs to turn or levers to adjust. The temperature of the heated lid can be changed or the heating function of the lid may be turned off.

With a footprint less than that of the average laboratory notebook, the TC-32 Mini Thermal Cycler will fit almost anywhere. Its reduced capacity block and economical price make the TC-32 Mini Thermal Cycler the perfect choice for lower throughput laboratories and educational facilities.
 

• “Mini” sized, 9 x 7 inch footprint
• Capacity for 32 x 0.2ml or 4 PCR Strips
• Intuitive touch screen control
• Program Wizard with familiar icon driven programming
• Optimize results with Accuris™ PCR reagents

A large, full color touch screen serves as the operations center where all functions are accessed. From the “Home” screen, simply touch an icon to view the last run program, enter the program library, or use the program wizard to quickly enter a protocol. In addition, icons for favorite programs can be added for faster access.

The program wizard guides users through quickly setting up a protocol in a single screen. Once entered, programs are shown graphically, and can be edited by simply touching the step that requires modification. Time and temperature increments can be built into programs as well as slower ramp rates. Storage capabilities are unlimited; programs can be stored in public folders, private (password protected) folders or on a flash drive. The full virtual keyboard allows for alphanumeric naming of programs and folders.

The fully adjustable heated lid prevents condensation and evaporation of samples. Lid temperature can be programmed, and when the block temperature is below 35°, the lid automatically shuts off. Heating and cooling of the block are precisely and accurately controlled within exceptionally tight tolerances by a proprietary algorithm that simulates sample temperature.

With the multi-format block, there is no need for the expense of multiple interchangeable blocks. The TC 9639 has the flexibility to accept 96×0.2ml tubes, a 96 well plate, 0.2ml strips or 39 x 0.5ml tubes all in the same sample block. For protocol optimization, a gradient can be set up across the block.  An optional in-situ adapter allows for incubation of slides. Additionally, the unit may be purchased with a 384 well sample block.

• Intuitive touch screen control
• Program Wizard – quick, easy & foolproof
• Unique multi-format block: 0.2ml tubes or strips (96), 0.5ml tubes (39), 96 well plate (1)
• Optimize results with Accuris™ PCR reagents

Operation is fully automatic, meaning all segments of operation (fill, sterilize, exhaust and dry) commence and run to completion by simply pressing “Start”. An optional thermal mini-printer is also available for providing a record of sterilization parameters. In addition, a built in USB port allows for transfer of these parameters to a computer for printing or storage of cycle data.

Both BioClaves offer three cycle options (standard programs), which are preset for the sterilization of liquids, wrapped instruments or unwrapped instruments/plastic ware. A “Dry Only” option is also available for additional drying time to be added to the end of a cycle. For special applications, requiring variations in cycle parameters, all settings on the BioClaves are fully adjustable.

• Accepts bottles/flasks up to 2L
• Fully automatic, just press start
• Adjustable sterilization times
• USB port for digital documentation of records
• Built in water tank, does not require connection to an external water supply

The “XL” model offers an increased chamber diameter of 35mm, making this product more suitable for the sterilization of larger objects, such as tube mouths or flask necks. Both models feature a lower temperature “standby” setting to extend the usable life of the heating element.

• Adjustable tilt angle, for more ergonomic inoculation (reduces hand fatigue)
• Same convenient operation as popular “Classic” model
• Available as “XL”, with wide chamber for sterilizing large vessels (tubes, flask mouths, etc.)

The ceramic heating element is safely enclosed in a perforated stainless steel guard chamber, protecting users from accidental contact with the extreme temperatures of the core area. It is extremely compact, convenient and can be used in anaerobic and aerobic chambers.

Research use only.

• Complete sterilization of loops, and tube mouths
• Safe, convenient and no spatter
• Eliminates the need for an open flame
• Ideal for research laboratories

• Stir up to 150-liter volumes
• Chemically resistant white ceramic top surface
• Powerful motor ideal for large vessel applications
• Digital control of both stirring speed and timer

Benchmark HCS Series of high-capacity stirrers provide reliable performance and safe operation for high throughput lab use. These stirrers feature a durable, chemically resistant white ceramic top plate, which protects the internals of the stirrer from leaks and spills. The powerful motor drive system ensures efficient and thorough mixing in large vessels and viscous samples.

Ideal for large-scale stirring applications, the HCS Series offers 50-liter and 150-liter maximum capacity models, as HCS-50L and HCS-150L respectively. Mixing speed can be viewed on the large digital display, and speed is adjustable from 50 rpm to 1500 rpm (HCS-50L) or 1200 rpm (HCS-150L). The built-in timer settings range from 1 second to 9 hours and include a continuous operation setting.

BENCHMARK™ INDUSTRIAL MULTI-POSITION HOTPLATE STIRRERS

The stirring speed is continuously adjustable from 100 to 1500rpm. For temperature sensitive samples, the MiniMag is incubator and cold-room safe for use from +4°C to +45°C.

• “Mini” sized, less than 3.5″ wide
• Adjustable speed control, 100 to 1500rpm
• Effectively mixes volumes up to 1.5L

Advanced microprocessor controls with convenient turn knobs allow quick, precise adjustment and maintenance of speed and temperature. Safety indicator LED’s on the front panel indicate when the heating and/or stirring functions have been activated. With a square 7.1 in work surface, all three models are compatible with a wide variety of popular sizes of borosilicate glass beakers, flasks, bottles and other vessels. The hotplate/magnetic stirrer model (H4000-HS) comes complete with a support rod for mounting thermometers and temperature probes.

• Ceramic work surface, 7.1 x 7.1 in.
• Stir speed from 60 to 1500 rpm
• Temperature control up to 380°C
• Three models: heat-stir, heat only or stir only

DRYCHILL™ ICE-FREE COOLING BLOCKS

• Maintains 0°C for up to 4 hours
• Also for use as a PCR workstation
• Two sides, ideal for: 1.5 & 2.0ml microtubes, 0.2ml PCR tubes & strips, 96 well PCR plates

• Contamination free mixing/homogenizing of samples
• Touch screen control with variable mixing speed and temperature control
• Adjustable stroke length to accommodate samples of various types
• Window for sample visualization
• Built in UV light for chamber decontamination

• LCD control panel
• Includes complete stand assembly
• Compact and quiet
• Digital accuracy and convenience

• Fast, reproducible sealing of well plates
• Adjustable time, temperature and pressure for optimized sealing
• User friendly controls, load plate and press run to seal
• Accepts a wide range of plate types and heights, including deep well storage plates, assay plates, pcr plates, etc.

• Intuitive, 7 inch color touch screen control panel
• Filter based system with wavelength range from 340 to 750nm
• Operates as a stand alone system, with USB flash drive drive for data transfer
• Absorbance range: 0.0 to 4.000 Abs 
• 8 channel vertical optical path, with zero dispersion
• Integrated, multi-speed plate shaker
• MR9600-T  features temperature controlled plate incubation

Automated System for Magnetic Bead-Based Purification

• Compatible with all popular magnetic bead kits

• Touch screen panel for on-board programming and operation

• Process up to 96 samples in deep-well plates

• 8-position carousel with 2 heating blocks

• Sample volume 50µl – 1000µl