PoE Testers Triplett Test Equipment & Tools Test & Measurement Products Malaysia, Selangor, Kuala Lumpur (KL), Shah Alam Supplier, Suppliers, Supply, Supplies

LELab Sdn Bhd
18, Jalan Sungai Burung U32/U,
Seksyen 32, Bukit Rimau,
40460 Shah Alam,
Selangor Darul Ehsan, Malaysia.

+603-5525 3833

+603-5525 3832

sales@lelab.com.my

+60125351036

PoE Testers

Power Over Ethernet - (POE-PL602)

Single Channel Power over Ethernet -- Power any pair, up to 46V.

Transmit Ethernet and Power signals together for PoE devices; Dip switch for power output: 12VDC/2A or PoE
Transmits data network signal up to 1, 000 meters over any pair of 2-wire such as Cat5, coaxial cable and power line, etc. The maximum physical bandwidth can reach 200Mbps.

IP Answer Stick IP Camera PoE Tester: Align and Focus IP Camera at Camera Location - (IPAS10-N)

The Triplett/ByteBrothers IPAS10-N IP Answer Stick is a must-have tool for IP camera installers. It allows users to align and focus the IP camera at the camera's location. The IP Answer Stick passes IP power through to the camera and has a port to connect your notebook computer. At the same time the stick also measures PoE voltage and power. No battery required. 1 year warranty.

Align/focus an IP camera on the jobsite using a laptop and camera software<
Configure a router at the router location; Configure an access point at its location
Monitor PoE volts, watts and link activity
No battery required; 1 year warranty

Includes:
IP Answer Stick only

Passive IP Extender Over Coax: Use Coax Cable to Send IP Camera Signal, Transmission Up to 984' - Pa

POE-1TR is a low cost and easy, speedy solution to allow you to use existing coax cable to send IP camera signal

PoE Tester Pro™ : Inline Power Over Ethernet Detector Detects PSE-Type/Class, Power Source and More

The POE2000 helps to speed up the installation and troubleshooting of PoE system devices. It can detect PSE-type/class, power source, polarity, voltage, current, power, and whether it is End Span (1/2, 3/6), Midspan (4/5, 7/8), or across all 4 pairs. If you are a VoIP phone and IP camera installer, you will know if there is power and a data pair available for your equipment. There is a test mode that can determine if a standard PoE (36 to 60V) or non-standard (11 to 60V) passive PoE is being used. For inline power level monitoring the display alternates between Voltage, Current and Power and incorporates a step button for selecting specific data to display. No batteries required, uses system power when connected to a device.

4 LEDs indicate IEEE802.3af or 802.3at/bt standard
Dual 7-digit LEDs indicate power source either end (A) Span (1/2, 3/6) or Mid (B) span (4/5, 7/8) or both for bt
2 Yellow LEDs indicate reversed polarity for power type
Display alternates between Voltage, Current and Power with a step button for selecting specific data to display

professional power over ethernet poe tester

PoE Tester Pro

Detects PSE-type/class, power source, polarity, voltage, current, power, and whether it is End Span, Midspan, or across all 4 pairs. When used inline, the display alternates between Voltage, Current and Power with a step button for selecting specific data to display.

Triplett Solutions for Every Contractor


Four LEDs indicate IEEE802.3af or 802.3at/bt standard.	Dual 7-digit LEDs indicate power source either End Span (1/2, 3/6) or Mid Span (4/5, 7/8) or across all four pairs.	Determines standard PoE or non-standard passive PoE.	Two yellow LEDs indicate reversed polarity for power type.

professional security camera installation poe detector and tester

Applications

This tester helps to speed up the installation and troubleshooting of PoE system devices. If you are a VoIP phone and IP camera installer, you will know if there is power and a data pair available for your