If higher speeds are required, we also offer e.g. an angle rotor with a max. RCF of 14532/16022 xg for 10 x 50 ml.

The fixed-angle and swing-out rotors are suitable for almost all aplications in everyday use in clinical, industrial and research laboratories.

Features and Functions:-
• Brushless induction drive
• Microprocessor control
• Active imbalance detection and cut-off
• Motor driven lid lock
• Automatic rotor identifi cation system with over speed protection
• Audible signal at the end of each run
• Emergency lid lock
• Stainless steel chamber
• CFC-free refrigeration system (-20° to +40°C)
• Autoclavable rotors

Display functions
• Diagnostic program
• Program memory for 99 programs
• Quick-key for short runs
• Pre-cooling program
• Standstill cooling
• 10 acceleration and 10 deceleration rates, possibility of unbreaked deceleration
• Permanent indication of preset and actual values
• Pre-selection of speed or RCF in steps of 50/10 increments
• Pre-selection of running time from 10 sec to 99h 59min or continious
• Simple one handed opertaion

If higher speeds are required, we also offer e.g. an angle rotor with a max. RCF of 14532/16022 xg for 10 x 50 ml.

The fixed-angle and swing-out rotors are suitable for almost all aplications in everyday use in clinical, industrial and research laboratories.

Features and Functions:-
• Brushless induction drive
• Microprocessor control
• Active imbalance detection and cut-off
• Motor driven lid lock
• Automatic rotor identifi cation system with over speed protection
• Audible signal at the end of each run
• Emergency lid lock
• Stainless steel chamber
• Pre-selection of running time from 10 sec to 99h 59min or continious
• Simple one handed opertaion     
• Air cooling
• Autoclavable rotors

Display functions
• Diagnostic program
• Program memory for 99 programs
• Quick-key for short runs
• 10 acceleration and 10 deceleration rates, possibility of unbreaked deceleration
• Permanent indication of preset and actual values
• Pre-selection of speed or RCF in steps of 50/10 increments

Both, the tube capacity of 40 x 15 ml conical tubes and centrifugal forces up to 24325 xg, making these table top centrifuge Z 366 K into a universal high-powered centrifuge.

Features and Functions:-
• Brushless induction drive
• Microprocessor control
• Active imbalance detection and cut-off
• Motor driven lid lock
• Automatic rotor identifi cation system with over speed protection
• Audible signal at the end of each run
• Emergency lid lock
• Stainless steel chamber
• CFC-free refrigeration system (-20° to +40°C)
• Autoclavable rotors

Display functions
• Diagnostic program
• Program memory for 99 programs
• Quick-key for short runs
• Pre-cooling program
• Standstill cooling
• 10 acceleration and 10 deceleration rates, possibility of unbreaked deceleration
• Permanent indication of preset and actual values
• Pre-selection of speed or RCF in steps of 50/10 increments
• Pre-selection of running time from 10 sec to 99h 59min or continious
• Simple one handed opertaion

Both, the tube capacity of 40 x 15 ml conical tubes and centrifugal forces up to 21379 xg, making these table top centrifuge Z 366 into a universal high-powered centrifuge.

Features and Functions:-
• Brushless induction drive
• Microprocessor control
• Motor driven lid lock
• Automatic rotor identifi cation system with over speed protection
• Audible signal at the end of each run
• Emergency lid lock
• Stainless steel chamber
• Air cooling
• Autoclavable rotors

Display functions
• Diagnostic program
• Program memory for 99 programs
• Quick-key for short runs
• 10 acceleration and 10 deceleration rates, possibility of unbreaked deceleration
• Permanent indication of preset and actual values
• Pre-selection of speed or RCF in steps of 50/10 increments
• Pre-selection of running time from 10 sec to 99h 59min or continious
• Simple one handed opertaion

The Z 327 K includes the refrigeration system on the back side of the unit, optimized for the lab bench at only 40 cm wide.

The Z 327 K includes the refrigeration system on the back side of the unit, optimized for the lab bench at only 40 cm wide.

The Z 306 offers many accessories, including rotors for microtitreplates and high-speed fixed angle rotors for reaction vessels or centrifuge tubes up to 50 ml. Additionally, swing out rotors, which hold a volume of up to 4 x 145 ml can be used for tissue culture tubes and also for all common blood tubes.

This wide range of accessories makes the Z 306 laboratory centrifuge indespensable in research laboratories and small clinical laboratories.

Features and Functions:-
•  Brushless induction drive
•  Microprocessor control
•  Active imbalance detection and cut-off
•  One-hand closing
•  Motor driven lid lock
•  Automatic rotor identification system with over speed protection
•  Audible signal at the end of each run
•  Emergency lid lock
•  Stainless steel chamber
•  Air cooling
•  Autoclavable rotors

Display functions
•  Diagnostic program
•  Program memory for 99 programs
•  Quick-key for short runs
•  10 acceleration and 10 deceleration rates, possibility of unbreaked deceleration
•  Permanent indication of preset and actual values
•  Pre-selection of speed or RCF in steps of 50/10-er
•  Pre-selection of running time from 10 sec to 99h 59min or continious
•  Simple one handed opertaion

No matter if angle, swingout, plate or hematocrit rotor you will always find the suitable accessory for your needs. Its appealing design and the innovative control panel with “Touch-operation” function and LED light, which indicates the current operating state, complete the versatility of this model.

Features and Functions:-
•  Maintenance-free induction drive Microprocessor with large LCD display
•  Electromagnetic lid lock
•  Automatic radio-frequency rotor identification system (RFID) with over speed protection, immediately upon rotor insertion
•  Active imbalance-identification and –cut off (rotor specific)
•  Rotor exchange is easy to handle
•  A large variety of rotors and accessories
•  USB interface for software updates via a
•  PC Manufactured according to international safety regulations, i.e. IEC 61010z. B. IEC 61010
•  Improved ventilation system keeps samples cool

Display functions
•  Control panel with Touch-Operation
•  Simply one-handed operation
•  Easy to program with gloves on
•  Spash-proof foil keyboard
•  Permanent indication of pre-set and actual values
•  Selection of speed in both rpm and g-force, in increments of 10
•  10 acceleration and deceleration rates, possibility of unbreaked deceleration
•  Pre-selection of the running time, from 10 s to 99 h 59 min
•  Storage of up to 99 runs  
•  Quick-key for short runs
•  Color visual representation of the operating state such as standstill, standby or centrifugation  

The Z 307 offers many accessories, including rotors for microtitreplates and high-speed fixed angle rotors for reaction vessels or centrifuge tubes up to 50 ml. Additionally, swing out rotors, which hold a volume of up to 4 x 200 ml can be used for tissue culture tubes and also for all common blood tubes.

This wide range of accessories makes the Z 306 laboratory centrifuge indespensable in research laboratories and small clinical laboratories.